Tel: +86-532-88566601
E-mail: sales@successrigging.com

Contact

Qingdao Success Machinery Co.,Ltd

ADD: Guozhuang Industrial Park, Tongji Subdistrict, Jimo Qingdao

 

TEL: +86-532-88566601

FAX: +86-532-85059139

 

E-MAIL: sales@successrigging.com

WEBSITE: www.successrigging.com

Shackle As Much As Possible To Reduce The Wear And Tear

Shackle in the course of the use will inevitably lead to wear and tear, the problem of wear is inevitable, we can do is to minimize the wear and tear of the Shackle, the company as a professional high-strength Shackle manufacturers, small tape with everyone to Learn how to reduce wear when the Shackle is in use.

 The wear and tear of the Shackle in use is inevitable, since it is inevitable, then we will minimize the wear and tear of the Shackle. In the process of using the elevator Shackle, please try to keep the conveyor Shackle in the large gear and the flywheel between the vertical. Shackle ball bearings used as a Shackle to take the wheel, the guide wheel are selected 16Mn material from deep processing. Our company's production of hanging Shackle life of more than 5 years to ensure the normal use of the user.

 Hoist Shackle has a good space, for a wide range of applications, can continue to work by non-stop through the high temperature drying Road, harmful gas area, spray paint room, before the treatment of paint, freezer, air storage, etc., to complete the artificial difficult to operate the production Process, thereby improving the working conditions of workers, improve product yield and quality. Shackle in the workshop of the material on the air distribution, the design of a reasonable program, the warehouse, assembly lines and other related nodes organic combination, to the maximum extent possible to rationalize the logistics of the workshop, resulting in greater efficiency.

Shackle use for some time, the need for lubrication of the Shackle, as a professional plate Shackle manufacturers, with you today to learn about the common lubrication of the Shackle method.

Ⅰ - artificial oil or oil brush regularly oil;

Ⅱ - drip oil lubrication, with oil cups through the tubing to the inside and outside the loose Shackle of the gap between the drop of oil;

Ⅲ - oil bath lubrication or splash lubrication, the use of sealed transmission box, the former Shackle and part of the sprocket immersed in oil, which uses a larger diameter of the oil pan oil splash;

Ⅳ - pump pressure fuel injection lubrication, oil pump through the tubing to the Shackle of continuous oil supply, circulating oil can play the role of lubrication and cooling. The kinematic viscosity of the lubricating oil used in the Shackle drive is about 20 to 40 mm2 / s at the operating temperature. Only the speed is very slow and can not supply the oil, it can be replaced with grease.

1, the sprocket mounted on the shaft should be no skew and swing. In the same drive assembly, the end of the two sprockets should be in the same plane, the sprocket center distance of 0.5 meters below the allowable deviation of 1 mm; sprocket center distance of 0.5 meters or more, allowing a deviation of 2 mm. But does not allow the friction sprocket teeth side of the phenomenon, if the two rounds are too large prone to off-line and accelerated wear. Care must be taken to check and adjust the offset when replacing the sprocket.

2, the Shackle of tightness should be appropriate, too tight to increase power consumption, easy wear and tear; too loose Shackle easy to beat and off the Shackle. The degree of elasticity of the Shackle is: from the middle of the Shackle to lift or press the two sprocket center distance of about 2-3cm.

3, the new Shackle is too long or elongated after use, it is difficult to adjust, see the situation to remove the link, but must be even. The Shackle should pass through the back of the Shackle, the locking tab is inserted outside, and the opening of the locking tab should be in the opposite direction of rotation.

4, sprocket wear serious, should also replace the new sprocket and the new Shackle to ensure good engagement. You can not replace the new Shackle or new sprocket separately. Otherwise it will cause poor engagement to accelerate the wear of new Shackles or new sprockets. Sprocket tooth surface wear to a certain extent should be used in time to turn (referring to the use of the sprocket). To extend the use of time.

5, the old Shackle can not be mixed with some of the new Shackle, or easy to produce in the drive impact, pull the Shackle.

6, the Shackle should be timely in the work of filling lubricants. Lubricant must enter the clearance between the roller and the inner sleeve to improve working conditions and reduce wear.

7, the machine long-term storage, the Shackle should be removed with kerosene or diesel cleaning, and then coated with oil or butter stored in a dry place to prevent corrosion.